{"id":57,"count":15,"description":"Pyrolysis (gas generator) boilers FOCUS \u2014 omnivorous equipment with maximum efficiency In the conditions of a stable decrease in the quality and quantity of solid fuel for the generation of thermal energy in Ukraine, consumers have to look for non-standard solutions, in particular, for the combustion of low-grade fuel. Manufacturers of heating equipment, for their part, are improving the methods of burning such fuel. Pyrolysis (or gas generation) technology has become one of the most effective and promising methods of generating thermal energy, showing high efficiency and allowing the use of a wide variety of fuels, including household waste. The principle of pyrolysis combustion is used in solid fuel <strong>pyrolysis boilers<\/strong>. FOCUS has been developing and operating pyrolysis boilers since 2014. During this time, it has identified and adapted all the nuances that arise during their operation, from the consumer and staff, and launched its own products on the market - reliable high-performance FOCUS pyrolysis boilers. The equipment is intended primarily for semi-industrial use, in boiler houses of agricultural and industrial enterprises, provides efficient and cost-effective heating of buildings and structures. The main advantages of FOCUS pyrolysis boilers In solid fuel pyrolysis boilers from FOCUS, you can use hybrid fuel, including pellets (burned with a pellet burner), firewood, fuel briquettes, furniture industry waste, plastic, household waste, etc., with minimal emissions into the atmosphere and without a characteristic unpleasant odor. For high-quality combustion of garbage, it should be combined with firewood or briquettes. The principle of pyrolysis combustion of solid fuel is as follows: under the influence of high temperatures (over 1100-1500\u00b0C) and in conditions of oxygen deficiency, the fuel decomposes into volatile (pyrolysis) gases and a solid residue. During pyrolysis decomposition, air heating is improved, which dries the fuel in the bunker, after which the fuel enters the combustion zone through the nozzle. Flue gas waste in such boilers has an insignificant concentration of harmful substances, carbon dioxide CO2 emissions are several times lower than the permissible norm. All thanks to the formation of a high-temperature torch - the supplied oxygen mixes with the released gases, active carbon is burned. The pipes are practically not clogged, the ash content is extremely low. Accordingly, if <strong>buy pyrolysis boiler<\/strong> instead of a conventional boiler, cleaning will be required much less often. Additional advantages of FOCUS pyrolysis boilers: special combustion chamber design. Combustion is directed from top to bottom. This allows adding fuel without stopping operation. For comparison, in a classic boiler, a new load does not burn until its entire volume is warmed up; due to the removal of a large amount of heat from fast-moving flue gases from a high-temperature torch, only the heat necessary to protect the chimney from condensation in severe frost is thrown out into the street, thereby increasing the efficiency of the equipment; the boiler can operate on pellets made at home and by hand, on lump fuel, gas coals (which practically do not burn in classic boilers), various briquettes, construction combustible waste. In such cases, the cost of heating autonomous households is reduced to a minimum with a level of comfort comparable to gas heating. Distinctive design features of FOCUS pyrolysis boilers The boiler consists of an afterburning chamber (lower) and a fuel bin (upper). Fuel is loaded into the upper chamber and prepared for pyrolysis (drying, heating, gasification). The combustion process begins at the bottom of the bin in conditions of oxygen deficiency. Then the released gases are mixed with oxygen and afterburning occurs in the lower chamber. The FOCUS pyrolysis generator boiler has a number of distinctive features and advantages that have no analogues from other manufacturers: fan air supply controlled by the ecoMAX 260 sensor controller (included in the delivery set); the controller controls the gasification chamber fan, boiler pump and DHW heating pump; there are 3 temperature sensors (boiler, DHW, flue gases), STB safety thermostat input, room thermostat sensor input; horizontal combined heat exchanger; the boiler is made of 09G2S steel from solid elements assembled according to the modular principle with minimal welding. The doors are thermally insulated and are not subject to thermal deformation at maximum operating parameters. The safety group is not included in the kit (purchased separately). If necessary, the manufacturer produces boilers of various capacities according to the standard range, for FOCUS pellet burners. Setting up and operation of pyrolysis boilers The FOCUS pyrolysis boiler is installed in a separate room of the boiler room. Setting up and adjusting is carried out taking into account the existing operating conditions. The automation of the equipment makes it possible to set the required fan pumping power, frequency and duration of blowing. The pyrolysis boiler is fired up according to the same principle as firing up other boilers. A small volume of the first batch is loaded into the chamber, ignition is performed. The main volume of fuel is added when combustion becomes stable. It is permissible to use large firewood, up to 20 cm in diameter. When using firewood, the duration of the boiler operation cycle can be 8-48 hours. The start of pyrolysis is accompanied by the overlapping of the chimney damper at a temperature above 60C. A torch is formed in the lower chamber. Additional fuel can be added at any time. The required operating power is achieved automatically by increasing the intensity of air supply to the combustion chamber. Forced blowing is switched off as soon as the nominal heat output is reached. The internal temperature can increase by inertia, after which it will gradually decrease. The boiler operates within the temperatures set by the operator. If there is a lack of oxygen, forced blowing is activated again. Cleaning and maintenance of pyrolysis boilers In a pyrolysis boiler, maintenance is required for 4 parts: chimney. It is performed before the start of the heating season and at its end; heat exchanger. By default, it is required once a week, but such a need may arise more often when using resinous firewood; hopper and air ducts of the nozzle. It is important to periodically clean the nozzle from ash particles; ash pan. Pyrolysis assumes minimal ash content. The accumulated ash is removed with a boiler tool. Economic feasibility of pyrolysis boilers In the conditions of constant rise in the price of gas and fossil fuels, the pyrolysis (gas generator) boiler FOCUS offers a profitable alternative - it provides a fairly complete processing of biofuel into generator gas at a high combustion temperature, which is the reason for the economic effect. In the pyrolysis (gas generation) mode, with the correct high-temperature combustion and a developed convective heat exchanger, the FOCUS boiler achieves a rare efficiency indicator - 92%! Maximum operating efficiency distinguishes this type of equipment from more expensive electric and classic boilers.\n\n<strong>Buy pyrolysis boilers FOCUS<\/strong> \u2014 it is profitable, since such equipment provides a quick payback due to high efficiency, as well as due to the transition to waste fuel, waste, combustible residues, inevitable during construction or repair work, in the production of various products (in the agricultural sector, printing, furniture production, and other areas of activity). A significant economic difference is a strong argument to consider waste from economic activities as an alternative fuel and not save on heat, heating all the necessary premises and open areas. Buying pyrolysis (gas generator) boilers FOCUS is a smart choice Pyrolysis boilers manufactured by the Ukrainian company FOCUS are durable, reliable equipment that meets international quality standards. High economic efficiency \u2014 savings on heating reach 500%. Efficiency factor \u2014 up to 92%, which no alternative heating system can boast of. The pyrolysis combustion process involves the use of various types of alternative fuel, including industrial waste and garbage, without polluting the atmosphere and requiring frequent maintenance. Utilization gains direct efficiency. Due to the automation of such equipment, a person does not need to constantly be near the boiler, and one working cycle can last up to 2 days. High power and large chamber volumes provide effective heating of large industrial, semi-industrial and residential premises. Buying a FOCUS pyrolysis boiler is a long-term investment with obvious benefits.","link":"https:\/\/firebox.com.ua\/en\/piroliznye-tverdotoplivnye-kotly-focus\/","name":"FOCUS solid fuel pyrolysis boilers","slug":"piroliznye-tverdotoplivnye-kotly-focus","taxonomy":"product_cat","parent":0,"meta":[],"menu_order":7,"_links":{"self":[{"href":"https:\/\/firebox.com.ua\/en\/wp-json\/wp\/v2\/product_cat\/57","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/firebox.com.ua\/en\/wp-json\/wp\/v2\/product_cat"}],"about":[{"href":"https:\/\/firebox.com.ua\/en\/wp-json\/wp\/v2\/taxonomies\/product_cat"}],"wp:post_type":[{"href":"https:\/\/firebox.com.ua\/en\/wp-json\/wp\/v2\/product?product_cat=57"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}