Vykoristovuetsya for laying a line for supplying the middle vice to the nozzles, for laying a line for drainage, for supplying water to the pumping unit. Vikonano made of linear polyethylene, increased hardness for reduced expansion under pressure, giving a sharp start/grooving on the nozzles. Stіyka to ultraviolet that ovnіshnіh ancestral minds. Diameter 6mm (1/4 inch).

Vykoristovuetsya for laying a line for supplying the middle vice to the nozzles, for laying a line for drainage, for supplying water to the pumping unit. Vikonano made of linear polyethylene, increased hardness for reduced expansion under pressure, giving a sharp start/grooving on the nozzles. Stіyka to ultraviolet that ovnіshnіh ancestral minds. Diameter 6mm (1/4 inch).

Vikorist is used to connect the sections of the main during installation, gaining the required doubling with 90*. To repair damaged plots, damaged passages, and other operations, it is necessary to connect two drainage lines, both the water supply and the middle vise line, drainage line, etc. Or you can change the line directly to 90* without breaking the highway.

Working vice up to 10 bar.

Vikorist is used to connect the sections of the main during installation, gaining the required doubling with 90*. To repair damaged plots, damaged passages, and other operations, it is necessary to connect two drainage lines, both the water supply and the middle vise line, drainage line, etc. Or you can change the line directly to 90* without breaking the highway.

Working vice up to 10 bar.

Vikorist is used to connect the sections of the highway during installation, collecting the required supply. To repair damaged plots, damaged passages, and other operations, it is necessary to connect two drain lines, both on the water supply and on the middle vise line, the drainage line.

Working vice up to 10 bar.

Nozzle with 0.3mm nozzle in a set with a tee — a ready-made kit for expanding the system, or replacing the main nozzles during the trial operation of the system. Yakіsnі і pіdіbrаnі components ensure minimization of the hour on pіdbіr possession and virіshennya of problem nutrition. Once you are ready, thought out that choice of decision - save your time and work. Shvidko roz'єmne z'єdnannya on yak_snih components guarantees yakіsny that svydky result.

The nozzle is protected for work with a pressure of 8-10 bar, and it is selected for efficient work in this range of pressure. Safe molding of droplets with a size of 10-40 microns, which is most suitable for molding the hanger when victorious on open maidanchiks, ensuring the cooling of the wind, freezing the saw and the coma. Romir krapel is the most optimal for open-air maidanchiks. For work in the field of minds of specialized workers, it is recommended to install nozzles with corundum sawing 0.2mm.

Vikorist is used for separating the water supply lines of the fog system and for separating the main line in the middle vise, switching, installing a nozzle. There are additional openings for fixation. A coupling system with a tube and a nozzle and a disconnection mechanism during recommutation have been introduced. The presence of humic pollutants will impair the tightness of the connection. When assembling the system, install the elements on silicone lubricant to protect the plastic and humic elements from drying over an hour.

Vikorist is used for separating the water supply lines of the fog system and for separating the main line in the middle vise, switching, installing a nozzle. There are additional openings for fixation. A coupling system with a tube and a nozzle and a disconnection mechanism during recommutation have been introduced. The presence of humic pollutants will impair the tightness of the connection. When assembling the system, install the elements on silicone lubricant to protect the plastic and humic elements from drying over an hour.

An injector with a 0.3mm nozzle complete with a tri-piece is a ready-made kit for expanding the system or replacing existing injectors during normal operation of the system. Clear and selected components will ensure that the time spent on selecting the right and most problematic foods is minimized. When you are ready to go, your solution is well thought out and selected - you save your time and work. Smooth combination of clear components guarantees a clear and quick result.

The nozzle is designed for work with a pressure of 8-10 bar, and is selected for effective work in this pressure range. It ensures the molding of droplets with a size of 10-40 µm, which is most suitable for molding the hanger when pouring on open trays, ensuring cooling in the air, protecting from sawing and lumps. The number of droplets is most optimal for closed maydans. For work in specialized areas, it is recommended to install nozzles with 0.2mm corundum sawdust.